MARINE with NANO GUARD Premium Wood Sealer

0 out of 5 based on customer ratings
(0 customer reviews)

SEAL-ONCE® MARINE with NANO GUARDTM Premium Wood Sealer deeply penetrates the surface to protect and stabilize wood against weather and caustic conditions, including salt water spray. This formula uses proprietary nano-polymers to create a long-lasting flexible breathable barrier by coating the wood fibers at the cellular level to provide protection from the inside out.

Our clear, non-film forming MARINE with NANO GUARD allows the wood to age naturally without decay, morphing to a rich silver-gray over time. We offer a full range of Semi-Transparent Tints that can be added to the clear formula. These tints operate as UV blockers to prevent the wood from graying while enhancing the natural grain and texture.

MARINE with NANO GUARD is completely eco-friendly, with zero VOCs, and is safe to use around open water, marine life, pets, plants and people.

Recommended Use:
Decks Docks Piers Railings Retaining Walls Outdoor Furniture Play Structures Fences Planters

FIND A RETAILER

OR

BUY ONLINE

Product Details

  • Eco-friendly
  • Zero VOCs
  • Non-toxic; will not harm pets, plants, people or marine life
  • Non-film forming, flexible breathable barrier
  • Eliminates warping & cupping
  • Prevents wood rot & decay
  • Prevents mold, mildew & fungi growth
  • Stabilizes & protects wood
  • Soap & water clean-up

 

 

  • All surfaces should be cleaned before sealing for best penetration and performance.
  • Clean all dust, debris and loose material. Remove oil, grease, algae, grime, mill glaze and mold and mildew stains with appropriate cleaners. Recommend SEAL-ONCE All Wood Cleaner
  • Test absorbency after cleaning by sprinkling water on surface. If the water does not readily penetrate the surface, stripping will be necessary to remove old coatings.
  • Do not use if air or surface temperature is below 45°F/7.22°C or above 95°F/35°C.
  • Do not apply in rain or when rain is imminent.
  • DO NOT THIN. Mix well. Stir contents or shake thoroughly prior to use.
  • Apply two coats wet on damp with a brush, pump-up garden sprayer, air-assisted and/or airless sprayer.
  • Use 17-19 tip and medium to coarse spray pattern. Brush out any puddles.
  • For best results, apply in the shade and out of direct sunlight.
  • When applying in direct sunlight and wood surface is hot, spray with a mist of water and apply Seal-Once immediately on dampened surface.
  • Apply to all surfaces. Apply SEAL ENDS ONCE® to wood ends.
  • Do not use with other waterproofing products.
  • Wood can be painted or stained as soon as it dries in approximately 2-3 hours, if SEAL-ONCE Semi-Transparent Tints are not being used.

 

  • Allow approximately 2-3 hours depending on temperature and humidity before subjecting surface to light foot traffic.
  • Allow 12-24 hours for full cure, depending on temperature and humidity.
  • When recoating, apply as soon as previous coat has penetrated and surface is damp, not wet.
  • Clean sprayer equipment and brushes with warm soapy water.
  • Disposal: soap and water cleanup; no special disposal procedure needed.

 

Surfaces that have been treated with SEAL-ONCE MARINE with NANO GUARD Premium Wood Sealer can be cleaned using a mixture of 1 gallon warm water, 14 oz. bleach, and 1 oz. of Dawn® dish detergent. Apply this cleaning solution with a sprayer and allow to sit for 20 to 30 minutes on the wood surface before rinsing with water using a garden hose with a nozzle.

This cleaning solution can be used to remove airborne mold and mildew stains, dirt and grime from the wood surface. MARINE with NANO GUARD will prevent and resist any water, mold and mildew penetration. Do not use oxidizers, corrosives, or strippers on surfaces that have been treated with MARINE with NANO GUARD.

Surfaces can be recoated with MARINE with NANO GUARD at any time. MARINE with NANO GUARD may need to be reapplied for fading tint color, surface damage, in heavily worn or high traffic areas, or in places where the surface may have undergone noticeable changes.

Before reapplying MARINE with NANO GUARD, clean the surface using the recommended cleaning solution above. Apply MARINE with NANO GUARD according to package instructions. When reapplying in small areas, lightly overlap onto areas previously treated with MARINE with NANO GUARD.